Artika Skylight Problems? Find Solutions Here

artika skylight problems

A skylight may give a room an incredibly eye-catching atmosphere. However, it’s not without its downsides. Because of its protruding nature, it’s more vulnerable to issues such as leakage.

The article will outline some of the common Artika Skylight problems and how you can solve them.

Common Artika Skylight Problems and How to Fix Them

If you’re having problems with your LED ceiling light panels, don’t panic. Several things could be wrong with your panel, and this section details how you can deal with them.

1. Quick LED Panel Problem Detection

Your LED panel might fail, but you don’t know where to start. Start by switching on the LED panel. Your panel has a driver failure if it does not flash or rarely illuminate.

2. The LED Panel Does Not Illuminate at All

You can test your LED panel by turning on the remote control and pressing the connect button. If the LED panel turns on, it works well. If not, pressing one of the buttons will cause a blinking light to appear on your LED panel’s display screen.

If there is no blinking light or you see no connection/alarm, try pressing the remote control and connect button again.

The LED panel does not illuminate at all

3. Driver Failure

A faulty LED driver may result from one of the following circumstances:

  • Connecting the AC to the driver’s DC output.
  • Connecting the AC to the driver’s DC input.
  • Connecting the constant current output terminal with the modulating light.

To avoid frequent driver failure on your LED panel, avoid connecting the phase line to the ground line since it can result in zero output and charging of the outer casing.

4. The LED Panel Flashes

If you notice flickering after just turning it off and on, then it is likely that the LED light panel is not working correctly. To check if this is the case, turn off the bulb before turning it back on again. If the voltage drops low enough to cause an issue, then there could be something wrong with your power supply unit.

5. If Only Some of the LEDs in the Panel Are Lit

The reason why some LEDs are fading is that the bulb has outlived the lamp. A LED bulb will gradually fade during its lifetime rather than burn out. The fading occurs typically after its specified lifespan.

LEDs have a theoretical life expectancy of around 50,000 hours, after which their luminosity will naturally decline by approximately 70 percent.

6. LED Failure

The first step is ensuring the power source is turned on. If you’re using a battery-powered device, ensure it’s connected to its outlet or a working one.

Next, ensure that your panel is connected correctly to this outlet and not just plugged into an extension cord if there are multiple outlets. Then, check that both ends of the plug fit well into their sockets. If they don’t, try replacing them with new ones before continuing further into the troubleshooting steps.

Problems with drivers and voltage conversion

7. Problems With Drivers and Voltage Conversion

LEDs have a significantly lower voltage requirement than the standard household grid. They have a LED driver, which converts AC power into the LED chip’s optimum DC power.

A sudden increase in voltage may be to blame if your home’s LED lights burn out unexpectedly. You can hire an electrical engineer to inspect your house’s voltage to resolve this issue or approach your utility company for assistance.

8. Problems With Poor Insulation, Ventilation, and Overheating

The temperature has a significant effect on LEDs. While it doesn’t produce light through heat, the panel could overheat if you install it in incompatible fixtures. Typically, one or more specific LED bulbs work with every fixture type.

Furthermore, even when the base fits securely, the lamp will still overheat if you install a bulb that is the wrong size in the fixture. When the radiator isn’t doing its job correctly, overheating will occur, thus reducing the lamp’s lifespan.

9. Frequent LED Defects

Incorrect installation, overheating, buzzing sounds, faulty drivers, and inaccurate color depiction are some of the most common issues with most LED light models.

10. Power Fluctuations

The dimming of the LEDs might also result from grid issues. For instance, the abnormally high demand for power, climate, or transformer problems might significantly impact the LED’s ability to perform normally. To fix this issue, you will need the assistance of an electrician.

Power fluctuations

11. Problems With Low-Quality LEDs

If the LED is not faulty for any of the preceding reasons, you likely have a low-quality bulb. If your Artika Skylight LED Panel 1×4 is very bright, consider an Artika Skylight Dimmer. Verify the Artika Skylight warranty and get in touch with the manufacturer right away to protect your investment.

12. LED Panels Failing Early

Did the LED ceiling lights panel in your home or business unexpectedly stop functioning after only a year despite the manufacturer marketing them as having a service life of up to 50,000 hours? Finding the root of the problem in a LED ceiling light panel will be difficult unless you have experience with LEDs. A trained electrician will fix your LED lights not working.

13. Fix High Temperatures

When the driver is under inadequate ventilation, the driver housing should be near the lamp housing. If feasible, make some thermal grease application on the contact area between the housing and the lamp housing to increase the heat removal efficiency of the driver, guaranteeing the Artika Flat Panel ceiling light durability.

Fix high temperatures

14. Operation on a Transformer

Measure the voltage across two terminals on an electrical circuit board with an ammeter or voltmeter. They should read close enough to 120VAC. If they do not match exactly but come close enough for all kinds of reasons, such as poor-quality wiring, then check whether these readings are correct using another device set up correctly on another circuit board nearby. 

15. Operation on Motion Detector

You can use a LED to indicate the status of a motion detector circuit. That will help you determine any problem with your circuit and take appropriate action. For example, if you want to know if the motion detector is active or not, then use a LED connected in parallel with its output terminal.

If it lights up, the voltage at that point is above 0V. Otherwise, it will remain dark (0V). You can also use flat LED ceiling lights as an indicator for other things, such as sensing battery low.

16. Checklist for External Faults

It would be best to consider several things when inspecting external faults on your Artika FLP 14-ON.

  • Ensure no connections are loose.
  • Make sure the fuse is good.
  • Check for power at the fuse box.
  • Check for power at the switch.
  • Check for power at the receptacle if there are multiple connections.
  • Inspect all screws on junction boxes and fixtures for tightness.

17. Checklist for Electrical Installation

Keep in mind the following things when installing a LED panel.

  • Ensure the circuit you are installing can support the load of your new LEDs.
  • Don’t leave LEDs turned on for more than 12 hours at a time, or they could overheat.
  • Avoid Artika Skylight installation without consulting the manufacturer’s instructions.
  • Be careful not to touch the LED bulbs with your fingers since oil from your skin can damage the bulbs.
Checklist for electrical installation

How To Select a Quality LED Panel?

When selecting LED panels, the most common consideration is the overall size. It’s dependent on whether you’re upgrading your outdated system with a new one, in which case the process will merely require the installation of new fixtures.

Having more bulbs doesn’t necessarily mean you’re using more electricity. Panel lights have come a long way in terms of output, power consumption, and lifespan, thanks to technological advancements. That translates to a decrease in energy use for the same illumination level. Thus, the panels’ efficiency rating is of great importance.

Furthermore, the higher the lumen number, the brighter the light. The ratio of lumens to watts indicates that reliable LED panels have more lumens per watt rating. Before purchasing a fixture, you must verify this requirement. For instance, Artika Skylight 3700 lumens is a reliable LED Panel.

Final Thoughts

Pinpointing the root of the most prevalent Artika Skylight problems requires patience. And most importantly, keep yourself safe by turning off the power supply before working on the lights, and only attempt repairs if you have the necessary skills and experience. If you don’t feel confident doing so, hiring an expert to fix your flat LED light is your safest and best bet.

Frequently Asked Questions

Is Artika Skylight dimmable?

Yes. It’s dimmable and distributes light evenly.

How do I install Artika Skylight?

Mount the Artika Skylight in the ceiling.

How bright are 4400 lumens?

4400 lumens brightness equals that of 4400 candles.

How do I turn off Artika lights?

Turning off the light requires flipping the switch on time, typically positioned right next to the motion sensor.

Why is my LED ceiling light flashing?

In most cases, the wiring is the root of the problem.