What you find on this page:
Is your Amana furnace not working as expected?
This article will help you to find all Amana furnace troubleshooting, error codes, and solutions.
Common Amana Furnace Troubleshooting and Repair
Here are all the details about Amana furnace troubleshooting and repair:
Amana furnace not igniting
The Amana furnace often does not ignite due to the poor or no power supply.
Check your electrical system and try resetting the furnace’s circuit breaker.
Furnace is igniting but not heating
Usually one or more blockages of dust or any solid object in air filters can stop your furnace from heating.
Cleaning the filter furnace frequently helps extend the life of your furnace.
If this doesn’t work, you can also replace the filter yourself by considering the steps below:
- Turn off your Amana Furnace or the thermostat.
- Find the filter, commonly located in the air-intake grill area.
- Slide the old filter out by considering which side the arrows are facing.
- After taking out the old filter, slide the new one.
- Now you are ready to turn on the device.
Irregular cycling happens
This error often occurs when your Amana Furnace turns on and off without attaininging the adjusted temperature on the thermostat.
Air blowing issues
Air blowing issues in Amana furnace including either excessive hot air blowing or not blowing air.
Water leakage
The Amana furnace shows leakage issues due to the holes and dripp in drain pipes and hose.
Check and replace pump, drain line, or drain hose to avoid leakage issues.
The Amana furnace keeps turning on and off frequently
The flame sensor monitors in your Amana Furnace detect the flame presence. If these sensors get damaged or have dirt on them, it can give false positives to the machine and turn on and off the furnace.
Check the sensor for dirt and clean it after completely turning off the furnace. If the sensor is damaged, you need to replace it.
Amana furnace noise
This glitch commonly occurs when the screws are not accurately screwed up, so their loose grip produces noise.
Usually, the noise is caused by loose screws, shaking the blower wheel. Tighten the screws or replace the blower wheel if it is damaged.
Other errors in furnace that need more attention
Furnace Not Heating
In case your furnace is not heating, it could ve for several reasons, one of them it’s a problem with the electrical system that provides power, or in other words, the power switch has been blown.
Check if you can reset the circuit breaker. If it’s in a bad state, then you need to replace this part. The other thing you want to check is the ignitor of the furnace. If there are any cracks in the ignitor, it needs to be replaced. Use a tool like a multimeter for the continuity test if you don’t find any cracks.
Furnace Blowing Too Much Air
If your furnace is blowing too much air, check the control board. The control board determines the required voltage amount for each part.
Replace the control board If there is any fault in the relay that controls the blower. If the relay fails, it will keep transferring excessive voltage to the motor.
It is also recommended to check the thermostat with a multimeter for continuity. If any issue is found in the thermostat, replace it.
Frequently Turning On And Off
The flame sensor monitors in your Amana Furnace detect the flame presence. If these sensors get damaged or have dirt on them, it can give false positives to the machine and turn on and off the furnace.
Check the sensor for dirt and clean it after completely turning off the furnace. If the sensor is damaged, you need to replace it.
Amana Furnace Troubleshooting and Repair
Here are all the details about Amana furnace troubleshooting to give you a clearer picture.
Amana Furnace Blower Speed Adjustment
If your Amana furnace is not warming, you must increase the blower speed. Keep increasing the blower speed using the circulator until you find the warmth matches your need. It will take some time to perform at the newly set rate.
Have Issues With the Filter?
Replacing the filter furnace frequently helps extend the life of your furnace.
You can replace the filter yourself by considering the steps below:
- Turn off your Amana Furnace or the thermostat.
- Find the filter, commonly located in the air-intake grill area..
- Slide the old filter out by considering which side the arrows are facing.
After taking out the old filter, slide the new one. Similar in the position to the old one. Now you are ready to turn on the device.
Amana Furnace Blower Motor Replacement
The blower motor can also be a troublemaker. Here’s how you can replace it.
Turn Off the Device
Turn off the furnace power, and close the gas valve before starting the replacement.
Remove the Assembly
Remove the blower cover panel, and unscrew the mounted screws. Note how the wires are connected, as you will need to connect them later. Unplug the motor wire. Now slide out the blower assembly.
Remove The Old Blower Motor
If your blower motor has a capacitor, unplug the wires and remove them. Disconnect the motor from the assembly by unscrewing the mounted screws.
Replacing The Blower Motor
Place the new motor in the assembly and screw it. Plug the capacitor back, if there is any. Slide in the blower assembly and connect all the wires like before. Place the cover panel back to its black and ensure it is properly shut.
Now turn on your Amana furnace. It should be working fine now.
Amana Furnace Pressure Switch Stuck On
Amana furnaces have a pressure switch built in them as a safety feature. Its function is to monitor whether there is any venting obstruction. There could be some reasons if your furnace pressure switch is stuck on. Here is how to troubleshoot it
Venting Issue
A blocked flue pipe makes combustion gasses elimination hard. Leafs, dirt, debris, dust, and snow can get stuck easily in the flue pipe of your furnace.
Check if there is anything stuck in the flue pipe, and you can clean it easily. After cleaning it, the pressure switch will not get stuck again
Broken Switch
If your furnace pressure switch is stuck on, it might be due to a broken or malfunctioning switch. Test the switch with a multimeter, and if it is faulty, replace it
Disconnected Hose
A disconnected pressure switch hose can be the reason your furnace pressure switch is stuck on. Check if the hose is connected correctly, which can be found above the gas burners.
Amana Furnace 6 Flashes
If your Amana Furnaces is flashing six lights, it can be due to a faulty flame sensor. Check if there is any dirt on the flame sensors. If there is any dirt, clean them after switching off your furnace.
If the flashes persist, try resetting the furnace by restarting it. If It keeps flashing, replace the flame sensors.
Amana Furnace Light and Error Codes
Amana Furnaces have built-in safety features that can communicate the error code. It’s a handy feature that can help the user know what is causing the issue in the furnace.
Red light Blinking
If the red light is constantly blinking, it means there is line voltage polarity or an issue in the wiring
Flashing 1 Time
If there is one flash, the issue could be related to blockage or interruption in gas supply, wiring, or flame rot not sensing flame. The solution is to find out the gas interruption and reset it by adjusting it to 20 seconds. The furnace will reset automatically once it is raised back.
Flashing 2 Times
2 Flashes indicate pressure switch shortage, interruption in vent, or the draft inducer might not be working. To resolve it, replace the draft inducer blower pressure switch or check for vent interruptions, such as dirt, debris, etc.
Flashing 3 Times
3 Flashes mean the issue is related to the pressure switch. Check if the switch is broken or not. Check if the switch hose is connected correctly.
Flashing 4 Times
4 Flashes refer to a blockage in the air filter. It can also mean that the drain tubes might be obstructed by dirt or moisture.
Flashing 5 Times
5 Flashes mean that the flame sensor is sensing heat without calling heat. It might be due to the valve closing slowly.
Flashing 6 Times
6 Flashes mean the flame sensor might be faulty or have some dirt on it.
Do you have any questions? Do not hesitate to contact our experts.
Conclusion
Amana furnaces, like every other home appliance, can cause issues, such as not heating, blowing air, or turning on and off. However, these problems can be fixed by cleaning the dirt and replacing the nuisance parts. The first step is to understand the error codes with light color and flash.
That said, let’s look at some frequently asked questions about the Amana furnace.
FAQs
Amana Furnace provides a 10-years warranty, which covers replacement parts. The part must be defective due to quality or regular use and maintenance materials. Additionally, they provide a lifetime heat exchanger limited warranty.
Check the flame sensor for any dirt if your Amaan Flancer flashes six times. If no dirt is found, you need to replace the flame sensor.
Yes, the Amana Furnaces can be reset very quickly.
Reset your Amana furnace by pressing the reset button, which you can commonly find in the blower compartment.
The Amana furnace blinks a red light to let the user know there is some fault in their furnace.
A solid red light indicates an issue in your Amana Furnace that you can identify by finding how often the red light blinks. If a red light is not blinking, no signal is received from the thermostat. There can be an issue with the connection.
Almost all Amana furnaces come with auto light functions built into them. If your furnace does not have an auto function, you can do it manually using the below techniques:
Find the furnace switch, which is generally located underneath the furnace, and switch it off. Wait for at least five minutes before moving to the next part.
After waiting for 5 minutes, find the reset button, which is located near the On and Off switch. Bring the long lighter flame near the pilot while holding the reset button. Let go of the reset button after the pilot is lit.
